Fulltext results:
- Serial communication @epulse50_dc_servodrive
- ====== Serial communication ====== The communication connector consists in a 4 pin connector with a serial UART,\\ __Note that you need a communication cable with USB to UART with 3.3V level.__ \\ thi... d that has the\\ following functions:\\ • grant a communication with a PC by USB\\ • gateway from drive to Wi-Fi\
- Connectors and indicators @gdi_ethercat
- Watchdog Timeout - Led Active|Red| |EL1|EtherCAT communication|Active - Connection to Ethercat|Orange| |EL2|EtherCAT communication|Blinking - Link port activity|Green| |EL3|EtherCAT communication|Active - Connection to Ethercat|Orange| |EL4|EtherCAT communication|Blinking - Link port activity|Green| ===== Conne
- NiLAB Starter Software @nilab_starter
- Parameter \\ - Unchecked Canopen Status update in communication window as Default \\ - Scope sampling time and le... 1.4] - 25.3.2025 \\ - ADDED DS402 STATE Coding on communication window \\ - Bug fix read/write of Gateway values ... 6.12.2024 \\ - Added Identification button on the communication windonw ## [2.4.0.3] - 18.11.2024 \\ - Added uPL... y. ## [2.3.1.0] - 26.03.2023 - Change of MODBUS communication library \\ - Improve of communication speed durin
- Connectors and indicators @nli_eth
- Watchdog Timeout - Led Active|Red| |EL1|EtherCAT communication|Active - Connection to Ethercat|Orange| |EL2|EtherCAT communication|Blinking - Link port activity|Green| |EL3|EtherCAT communication|Active - Connection to Ethercat|Orange| |EL4|EtherCAT communication|Blinking - Link port activity|Green| ===== Conne
- MODBUS RTU Communication @integrated_drive_motors
- ===== MODBUS RTU Communication ===== ==== Communication interface ==== the integrated drive linear motors are provide with MODBUS RTU communication interface for programming. Any PLC with MODBUS RT... m of 2 registers per read operation with standard communication speed of 38400 and parity Even. The MODBUS parame
- Starter interface windows @nilab_starter
- jpg?direct&800x376|motor_param_screen.jpg}} ==== Communication ==== MODBUS RTU communication console with scanning MODBUS nodes functionality to simply identify the motors connected to the bus. {{:nilab_starter:communication_screen.jpg?direct&800x376|communication_screen.jpg}} ==== Diagnostic ==== Simple and complete diagnostic tool
- NL7 Servo Drive @nl7_servo
- vides advantages as listed below. * **Lengthen communication range and lower electromagnetic interference** Du... rupted by electromagnetic interferences. EtherCAT communication protocol provides fault detections limitations and error handling that makes communication more reliable over long distances. * **Greater... * **Simplify complex wiring work** Using EtherCAT communication protocols, the connections between master device
- Use Cases @gtw_ethercat
- d motion trigger synchronization signal using CAN communication instead of Remote I/O signal. The NLi motor must ... tion table parameters is made by using MODBUS RTU communication. Status and control word can be read and write using MODBUS RTU communication. Current position can be read using MODBUS RTU.
- MODBUS RTU Interface @integrated_drive_motors
- iature linear motors are equipped with MODBUS RTU communication interface.\\ More information about this type of ... m of 2 registers per read operation with standard communication speed of 38400 and parity Even. The MODBUS parame... direct&800x379}} ==== Standard Device for MODBUS Communication with NLi integrated motor ==== === TOP7 PLC Touc
- Interface description @nilab_starter
- erface description ===== ==== Overview ==== - Communication Port (example: COM2, COM3,..) - Button to establish a communication with the motor - Button to donwload the configu... tion (motion, controller, scope, motor parameter, communication, diagnostic, espert and survelliance) - Motion
- Bus Interface Command and Status @gtw_ethercat
- nning|Cyclic running| |0x03|Alarm Can|Can timeout communication| |0x04|Alarm Modbus|Modbus timeout communication| |0x08|Flash Fault|Flash fault when try to write data|
- Bus Interface Configuration @gtw_ethercat
- === Bus Interface Configuration ====== ===== Bus Communication ===== Configuration of the Bus Interface is on S... CanOPEN bus speed can be changed using MODBUS RTU communication, writing on register 0xEF (254d). ===== PDO slav
- MODBUS Communication with CODESYS @integrated_drive_motors
- ====== MODBUS Communication with CODESYS ====== ==== CODESYS General configuration ==== In order to communication with NLii motor using MODBUS RTU interface please
- MODBUS Trigger Configuration @nilab_starter
- ere are two ways to start the motion using MODBUS communication: - Using broadcast message (special message to send using RS485 communication) - Writing the modbus sync signal register -
- How to save and reload the configuration @nilab_starter
- of the connected motor and the right COM port for communication using USB to RS485 adapter cable. In the example ... ailable motor with the relative ID number use the Communication window and the press the button Scan Modbus Nod