Fulltext results:
- How to save and reload the configuration @en:nilab_starter
- n Modbus Nodes to see the list. Press the button connect to Motor to connect. === {{:nilab_starter:connect.jpg?direct&800x378|connect.jpg}} === 3. Please verify that the expert window is disable and tghe write en
- Power Port Pinouts @en:nl7_servo
- \\ 1) Optional isolation transformer \\ 2) Do not connect to 380 VAC directly to prevent damage to drive \\... ase of serious interference, it is recommended to connect a line filter to main power supply; \\ \\ It is ... tor selection and connections| |N| |Please do not connect| |U|Motor U phase terminal| \\ Please ensure prop... ase of serious interference, it is recommended to connect a line filter to main power supply; \\ \\ It is
- MODBUS RTU Interface @en:integrated_drive_motors
- he motor configuration ==== Using NILAB Starter, connect to the single motor and store a different address... otors:modbus_id.jpg?direct&800x378}} ==== How to connect the motors on the BUS ==== The NLi integrated mi... the NL-DB15-MG6 terminal block from NILAB, please connect earth to ground, all grounds present must be conn... eck Avoid download parameter from drive checkbox, Connect to the right COM port using CONNECT to MOTOR butt
- Protection
- life, danger of injury by electric shock!** \\ * Connect the electrical equipment, the housings of all ele... ram. This is necessary even for brief tests. \\ * Connect the safety conductor of the electrical equipment ... \\ * Before startup, even for brief tests, always connect the protective conductor (ground wire). Otherwise
- Startup and operation @en:integrated_drive_motors
- ki/doku. php?id=nilab_starter:start ===== How to connect and program the motor using PC using programming ... NILAB Starter Software and then press the button “Connect to Motor”. ===== How to connect and program the motor using PC using USB to RS485 with two motors =====
- RS232 interface, PC connection (C2) @en:mbd_servo_drive
- is electrically isolated, however, is required to connect and disconnect the PC interface (C2) only with th... with a drive first of all it's necessary to: 1. connect physically the drive to the PC\\ 2. correctly co... ort, corresponding to the port physically used to connect the drive to the PC\\ 3. make sure that “Baud Rat
- Programming box DA012060 @en:nilab_starter
- or Ethernet to MODBUS RTU gateways. ==== How to connect ==== First step is to plug the USB cable into th... NILAB Starter Software and then press the button "Connect to Motor". ==== Connect using communcation window ==== |**Item** | | Button to scan modbus nodes to sear
- Encoder Calibration @en:reverso_encoder
- rogramming cable is connected (1), then press the CONNECT TO ENCODER button (2) to establish a connection. ... ?direct&850x433|encoder_reset.jpg}} After Reset, connect again to the encoder by pressing the CONNECT TO ENCODER button.
- How to activate AES Encryption @en:integrated_drive_motors
- ial communication channel follow these steps: 1) Connect to the motor using [[:en:nilab_starter:start|NILA... 1024x482|aes_2_correct.jpg}} 3) Before press the Connect to Motor button select the AESV Cryptography chec
- Programming box DA012060 - cable connections @en:integrated_drive_motors
- ated drive motors. The programming box is used to connect the PC to the motor during commissioning and firm... nection notes ===== - Use the programming box to connect the PC to the motor for commissioning and firmwar
- Wiring Diagram @en:nl7_servo
- oltage. | | Please take note of the capacity when connect to a 24VDC switching power supply, especially if ... oltage. | | Please take note of the capacity when connect to a 24VDC switching power supply, especially if
- USB Programming cable @en:epulse50_dc_servodrive
- === A USB-to-serial programming cable is used to connect the PC to the drive during commissioning. It conv
- Parametrization @en:epulse50_dc_servodrive
- arter_3.jpg}} ===== Configuration steps ===== - Connect the drive to the PC with the USB programming cabl
- Thermal Sensor @en:green_drive_iso
- (1.1 kΩ) triggers a fault and stops the drive. - Connect the sensor to the drive according to the connecti
- Accessories @en:green_drive_motors
- Accessories ===== ==== Linear coupling ==== To connect the payload with the slider, a coupling system is