Fulltext results:
- Technical characteristics @mbd_servo_drive
- ined by the used operating mode. ===== Technical data ===== {{:mbd_servo_drive:tech_data_1.jpg?nolink&800x340|tech_data_1.jpg}} {{:mbd_servo_drive:tec_data_2.jpg?nolink&800x336|tec_data_2.jpg}} ===== Environmental data ==
- Repeatability @green_drive_motors
- eviation, σ (sigma), indicates spread of measured data and is calculated by the following formula: {{:g... ity.jpg}} Where n is the number of sample in the data set, x_i is the value of data point and μ is the average value of data set. In a normal population of data points 99.7% of all test d
- Codesys / TwinCAT Integration @gtw_ethercat
- ctory and then restart TwinCAT. ===== PDI - Input Data Structure ===== A maximum of 10 NLi motors can be mapped at the same time. |**Address** |**Data Type** |**Description** | |0x6000|UINT16|Status| ... INT16|INPUTS (Remote Inputs)| ===== PDO - Output Data Structure ===== |**Address** |**Data Type** |**Description** | |0x7000|UINT16|GTW_CONTROL_WORD| |0x700
- Pacdrive 3 - Schneider Electric @reverso_encoder
- ase, if the motor is different consider the right data using datasheet engine: [[https://www.ni-lab.onli... s on the power port must be arranged). The Motor Data must be stored in the Drive Memory, with these in... store_location.jpg}} In order to store the motor data, switch Sercos phase to 2. Create the mdf file set to TRUE the xFile variable, then Delete the data inside the drive setiing xEnable_Delete and xExec
- Pacdrive3 - Lxm62 servo drive @green_drive_motors
- jpg}} It create a file inside the flash with the data of the structure ===== 4. Delete actual data inside the drive ===== Before all you must set the sercos phase to 2\\ Then you must delete any data inside the drive with this function block. {{:gr... 1.jpg?nolink&951x168|func_1.jpg}} If there is no data inside the result show this situation. If all the
- Siemens Sinamics S120 / G120 @green_drive_iso
- , the correct sequence to follow is: 1) Fill the data as in the table below (two example motor are list... listed in the table__. 2) The equivalent circuit data p350 and p356 will then need to be re-entered aft... n, the U and V phases must be swapped. 5) If the data already exists, only P431 and P1982=0 need to be
- Siemens Sinamics S120 / G120 @green_drive_motors
- , the correct sequence to follow is: 1) Fill the data as in the table below (two example motor are list... fication procedure**__ 2) The equivalent circuit data p350 and p356 will then need to be re-entered aft... n, the U and V phases must be swapped. 5) If the data already exists, only P431 and P1982=0 need to be
- Position table @gtw_ethercat
- ow level, 5→ Can Sync) {{:gtw_ethercat:pos_table_data.jpg?nolink&560x286|pos_table_data.jpg}} In order select the current slave ID to read and write, the SL... d. Every time this value is changed the POS_TABLE data are udapted.\\ Every SDO write on these registers
- MODBUS RTU Communication @integrated_drive_motors
- 63| |Output Variables|4608|4671|63| |Oscilloscope data|4672|6723|2051| |Diagnostic data logging temperature|7000|7512|512| |Diagnostic data logging current|7513|8025|512| === Command Word -
- WEBSMART Motor sizing
- nd rows the time resolution and then the position data point \\ with unit in meters {{:websmart_2.jpg?d... d. === A summary window with all the application data will be shown. {{:websmart_6.jpg?direct&800x580}
- MODBUS RTU @epulse50_dc_servodrive
- e and set the speed |**Command** |**Address** |**Data Write** |**Unit** |**NOTE** | |Opmode|0x0010|2|-|... tus and the current |**Command** |**Address** |**Data Write** |**Unit** |**NOTE** | |Enabling OK|0x1200
- Bus Interface Command and Status @gtw_ethercat
- 0|Running|Cyclic running| |0x01|Commit|Update the data on the slave with confirmation| |0x02|Reset|Reset... |0x04|Alarm Modbus|Modbus timeout communication| |0x08|Flash Fault|Flash fault when try to write data|
- EtherCAT to MODBUS RTU Gateway @gtw_ethercat
- or read or write| |0x800D Subindex 4|SLAVE_MODBUS_DATA|Current MODBUS RTU Data read or to write| |0x800D Subindex 5|SLAVE_MODBUS_FUNC_CODE|MODBUS RTU Function
- Faults Diagnosys and reset @integrated_drive_motors
- |STORE_CONFIG_TO_FLASH_ERROR|Problem to store the data inside the Flash memory|Try to reset the system u... signal usign oscilloscope, check the calibration data inside the expert window usign NiLAB Starter. Par
- Attraction force @ironcore_motors
- rces at the nominal air gap are specified in each data sheet of a motor in “Technical data”.** ===== Air-gap-related attractive forces between the primary an