Fulltext results:
- WEBSMART Motor sizing
- y the operating condizions of the motor. === For example, an external payload of 1.2 kgs and a motor type ... am profile file based on position points. Here an example of motion profile file:{{:cam_profile_example.zip|:cam_profile_example.zip}} \\ This example must contains as in the first rows the numerf of position p
- HSB (Hall sensor Box) linear positioning system @ironcore_motors
- the secondary part. The following scheme shows an example of mounting with left cable direction. {{:ironco... _5.jpg?nolink&500x204|hsb_5.jpg}} ===== Mounting example ===== ==== HSB-L version ==== 3D Model file: {{... .zip}} {{:ironcore_motors:hsb-l_mounting_drawing_example.jpg?direct&800x402|hsb-l_mounting_drawing_example.jpg}} ==== HSB-R version ==== {{:ironcore_motors:hsb-r
- Formatting Syntax @wiki
- links. These are quick links to other Wikis. For example this is a link to Wikipedia's page about Wikis: [... inks. These are quick links to other Wikis. For example this is a link to Wikipedia's page about Wikis: [... t formats for maximum browser compatibility. For example consider this embedded mp4 video: {{video.mp4|... the video and be either a jpg or png file. In the example above a ''video.jpg'' file would work. ===== Lis
- Safe Torque Off @gdi_ethercat
- l switch (Emergency button) ===== {{:nli_eth:sto_example_1.jpg?nolink&800x297|sto_example_1.jpg}} ===== Safety PLC ===== For example: Safety PLC output or safety sensors (e.g. Safety light curtain, safety scanner etc.) {{:nli_eth:sto_example_2.jpg?nolink&800x332|sto_example_2.jpg}}
- Can Open Fieldbus @integrated_drive_motors
- tors:can_open_pdo ==== Codesys configuration and example ==== {{:integrated_drive_motors:codesys_logo.jpg... cation_note_codesys.pdf}} * Single axis CODESYS Example: {{:integrated_drive_motors:1_axis_nli_example.project.zip|:integrated_drive_motors:1_axis_nli_example.project.zip}} * For more information about Codes
- Safe Torque Off @nli_eth
- l switch (Emergency button) ===== {{:nli_eth:sto_example_1.jpg?nolink&800x297|sto_example_1.jpg}} ===== Safety PLC ===== For example: Safety PLC output or safety sensors (e.g. Safety light curtain, safety scanner etc.) {{:nli_eth:sto_example_2.jpg?nolink&800x332|sto_example_2.jpg}}
- MODBUS Communication with CODESYS @integrated_drive_motors
- jpg}} Then configure the slave channels, here an example: {{:integrated_drive_motors:codesys_slave.jpg?nolink&1424x438|codesys_slave.jpg}} ==== Example ==== {{:integrated_drive_motors:rasp_example.jpg?direct&800x448}} Project example using Raspberry CODESYS PLC: {{:nilab_starter:raspberry_plc_pi4_modb
- Mounting example @reverso_encoder
- ====== Mounting example ====== Here an mounting example in combination with L075P-6015 primary part with L075S reduced weight magnet (L=192mm). {{:reverso_encoder:mounting_example.jpg?direct&1000x393|mounting_example.jpg}}
- SIN/COS 1Vpp Output Signal @reverso_encoder
- ====== SIN/COS 1Vpp Output Signal ====== Example of SIN/COS Output (Blue and Yellow) with the encoder conf... der:sin_cos_2.jpg?direct&650x449|sin_cos_2.jpg}} Example of SIN/COS Output (Blue and Yellow) with the enco... sin_cos_4_1.jpg?direct&650x394|sin_cos_4_1.jpg}} Example of SIN/COS Output (Blue and Yellow) with the enco... der:sin_cos_8.jpg?direct&650x468|sin_cos_8.jpg}} Example of SIN/COS Output (Blue and Yellow) with the enco
- Protection
- ect contact must be prevented by other means, for example, by an overcurrent protective device. \\ * Electr... ls must be installed in a protective housing, for example, in a control cabinet. \\ \\ **High electrical v... pping after switching off the motor power by, for example: \\ - mechanically securing the vertical axes \\
- Lexium32M Drive @green_drive_motors
- ta will be imported following the steps below. __Example of TPMConfig file__: GD250XS ⇒ {{:green_drive_mo... please reduce of 20% the speed gain (Kpn). ==== Example of starting control loops parameters ==== {{:green_drive_motors:parmeters_example.png?nolink&393x148}}
- Use Cases @gtw_ethercat
- parameters is made by using CanOPEN SDO. Codesys example project: {{:gtw_ethercat:gtw_eth_2_axis_pdo_sync_... nt position at every EtherCAT sync time. Codesys example project: {{:gtw_ethercat:gtw_eth_2_axis_pdo_io_sy... t position can be read using MODBUS RTU. Codesys example project using FCT640 PLC : {{:gtw_ethercat:gtw_et
- Master and slave mode @integrated_drive_motors
- lave.jpg?direct&700x419|master_slave.jpg}} ===== Example of configuration of the two axis ===== The waiti... s the homing speed, please specify low speed (for example 10mm/sec) in the master motor and medium speed (for example 50mm/sec) in the slave motor.\\ This to guarantee
- uPLC example programs - Instruction List (IL) @integrated_drive_motors
- ====== uPLC example programs - Instruction List (IL) ====== In order to write or edit the program please u... OUT 4096.2\\ END {{:integrated_drive_motors:sim_example.jpg?nolink&296x243|sim_example.jpg}} ===== 2) Enable the motor after 6 seconds from plc start ===== This
- OPMODE “Analog Speed”: software setting @mbd_servo_drive
- uts and analog input 1. Digital inputs setting: Example:\\ Setting Input 1 in position 1: Enable Drive an... s reseted.\\ Setting the analog input 1 scaling. Example:\\ Setting Analog In1 Scale = 9000mV and supplyin... in "Max Speed" parameter on Speed Window, in our example, the motor will rotate at 5000rpm. By providing -