Fulltext results:
- Protection
- er to operate electrical equipment, certain parts must unavoidably have dangerous voltages applied to th... s. \\ * Before switching on power the ground wire must be permanently connected to all electrical units ... arts with voltage higher than 50 V, the equipment must be disconnected from the mains voltage or power s... residual-current-operated protective device (RCD) must not be used on electric drives! Indirect contact
- Installation @mbd_servo_drive
- === Preliminary notes ===== \\ The MBD amplifier must be put into operation as an integrated component ... on of accidents and residual risks The installer must know and observe the following standards:\\ IEC 3... cident prevention regulations or BGV A2 The user must produce a risk analysis for the machine and must implement appropriate measures to ensure that unforese
- Siemens Sinamics S120 / G120 @green_drive_iso
- read_datasheet.php]]\\ Rated current of the motor must be fullfilled from the rated current of the drive... t possible.** \\ So, this identification function must be deactivated and the commutation angle must be manually entered. \\ (Parameter p1982=0)| ===== Motor feedback connection ===== The motor feedback must be connected using driveCliq converter SMC20 or S
- Transportation and storage @green_drive_iso
- tation and storage ===== Products in store rooms must be designated with a warning plate (ATTENTION! STRONG MAGNETS!).\\ Products must never be stored without a cover, always a special... tic packing with the electromagnetic gap of 25 mm must be used.\\ Warning plates must be read and complied with. Store rooms must be protected against weather
- Transportation and storage @green_drive_motors
- tation and storage ===== Products in store rooms must be designated with a warning plate (ATTENTION! STRONG MAGNETS!).\\ Products must never be stored without a cover, always a special... tic packing with the electromagnetic gap of 25 mm must be used.\\ Warning plates must be read and complied with. Store rooms must be protected against weather
- Transportation and storage @integrated_drive_motors
- tation and storage ===== Products in store rooms must be designated with a warning plate (ATTENTION! STRONG MAGNETS!).\\ Products must never be stored without a cover, always a special... tic packing with the electromagnetic gap of 25 mm must be used.\\ Warning plates must be read and complied with. Store rooms must be protected against weather
- Master and slave mode @integrated_drive_motors
- ster and slave mode ====== when two or more axis must be syhncronized without PLC that send a trigger s... == Pin 12 (Digital output 2) of the master motor must be connected to Pin 9 (Digital Input 1) of slave motor\\ Pin 8 (Digital input 0) must be set to 24VDC to start the motion. {{:integrat... s ===== The waiting time of the master and slave must be set to a__ waiting time of 5 msec__ (1). On th
- Installation tolerances @ironcore_motors
- he entire travel length, a defined air gap height must be guaranteed. For this purpose, the individual p... and secondary of the linear motor in the machine must be within a certain tolerance above the entire tr... from weight, attractive forces and process forces must be taken into account. A deviation of the specifi... material of the counterpart and length of thread must be designed with respect to the acting forces.\\
- Requirements on the design
- rties of linear direct drives, the machine design must meet various requirements. For example, the moved... apability, the mass of the moved machine elements must be reduced to a minimum. This can be done by usin... echanical structure. The goal of the construction must be to obtain an axis structure that is as compact... ot constantly moving (e.g. due to workpieces that must be machined differently) change, so that the natu
- Safety instruction
- ssed on to others, then these safety instructions must be delivered with the equipment. | {{:integrate... oted in these instructions. * Furthermore, they must be trained, instructed and qualified to switch el... to the requirements of safe work practices. They must have adequate safety equipment and be trained in ... ent conditions given in the product documentation must be observed. * Use only safety features and app
- Pacdrive3 - Lxm62 servo drive @green_drive_motors
- ===== ===== 1. PLC Configuration ===== The axis must be set as Lexium62 linear drive inside the Machine Expert and the motor indentification must be set as motor without type plate. {{:green_dri... To create the typeplate file inside the flash you must use this function: {{:green_drive_motors:functio... ctual data inside the drive ===== Before all you must set the sercos phase to 2\\ Then you must delete
- Siemens Sinamics S120 / G120 @green_drive_motors
- read_datasheet.php]]\\ Rated current of the motor must be fullfilled from the rated current of the drive... tor feedback connection ===== The motor feedback must be connected using driveCliq converter SMC20 or S... to calculate|to calculate| *) Note that the P341 must be calculate using __**Pole Position Identificati... s, these values are overwritten. The calculations must be performed to provide consistent values for the
- Liquid Cooled Motors (LK) @ironcore_motors
- d Cooled Motors (LK) ====== Liquid cooled motors must have a proper closed loop cooling circuit. The co... e addition of anti-corrosion agent. Such products must be compatible with all the components of the circ... d servo motor.__ Inlet cooling media temperature must be between 5° and 25°C to avoid condensation insi... motor; in any case the inlet coolant temperature must be higher than the motor frame temperature of at
- Motor components arrangement @ironcore_motors
- higher stress than in a single arrangement. This must be taken into account when the drive is selected.... 4.jpg}} To ensure successful operation, the axis must fulfill the following requirements in parallel ar... on. To ensure successful operation, the primaries must be arranged in a specific grid. The determination of the grid sizes that must be adhered to depends on the direction of the cab
- Directives @mbd_servo_drive
- tage Directive (2006/95/EC)\\ The following rules must be applied in accordance with Directive 98/37/EC\... (Safety of Machines) \\ The machine manufacturer must produce a risk analysis for the machine and must implement appropriate measures to ensure that unforese... age to persons or property.\\ The following rules must be applied in accordance with Directive 2006/95/E