Fulltext results:
- Connection system @integrated_drive_motors
- S|TERMINATION RESISTANCE| | |10|DIG_OUT_0|Digital output 0 (24V logic,PNP)|Motor running| |11|DIG_OUT_1|Digital output 1 (24V logic, PNP)|Motor fault| |12|CAN_L|CAN LOW... (24V logic)|Motion trigger| |10|DIG_OUT_0|Digital output 0 (24V logic, PNP)|Motor running| |11|DIG_OUT_1|Digital output 1 (24V logic, PNP)|Motor fault| |12|DIG_OUT_2|Dig
- Inputs and outputs connection @epulse50_dc_servodrive
- * | |C2|43025-1600|Molex|16 poles male, for input/output/can (Receptacle Housing)| ==== Outputs electrica... se30** |**Epulse50** |**Epulse 100** |**Unit** | |Output type|open collector NPN|open collector NPN|open collector NPN|-| |Output current|0,5|2|2|A| |Pulse peak current|1,0|4|4|A|... ent|30mA @ 24VDC|30mA @ 24VDC|30mA@24VDC|-| ==== Output signal schematics ==== {{:epulse50_dc_servodrive
- Input / Output Signals @integrated_drive_motors
- ====== Input / Output Signals ====== ** <font inherit/inherit;;#e74c3c;;inherit>PLEASE PAY ATTENTION ABOUT THE CONNECTIONS BETWEEN OUTPUT SIGNAL OF THE MOTOR AND THE PLC !</font> ** ** ... LOW RESISTANCE LOAD WHEN THE MOTOR IS ENABLED THE OUTPUT PNP TRANSISTOR WILL BE DAMAGED PERMANENTLY.</font... ors:io_sig.jpg?nolink&500x365|io_sig.jpg}} ===== Output Signals ===== ==== PNP - Default type (Default t
- Service Bulletin - Integrated Drive miniature linear motors @service_bulletin
- FROM S/N: DA00013650** **ACTION:** * Digital Output protection and output type change * Added PTC protection on the 3 digital output * Changed the output type from NPN with pull-up to PNP open drain. **WARNING:** Please take into acco
- Integrated Encoder @green_drive_iso
- with integrated SIN/COS 1Vpp encoder. The signal output is differential type with a refernce of 2.5V. The... lines : SIN+, SIN-, COS+, COS- that represent the output of the encoder system.\\ The integrated encoder m... digital interpolator. Using this electronics, the output signal is programmable up to 8192 increments per ... ss_interface_logo.png?nolink&150x56}} The signal output is differential type A+/A- and B+, B- TTL 5V. BiS
- Integrated Encoder @green_drive_motors
- with integrated SIN/COS 1Vpp encoder. The signal output is differential type with a refernce of 2.5V. The... s lines : SIN+,SIN-,COS+, COS- that represent the output of the encoder system.\\ The integrated encoder m... digital interpolator. Using this electronics, the output signal is programmable up to 8192 increments per ... ss_interface_logo.png?nolink&150x56}} The signal output is differential type A+/A- and B+,B- TTL 5V. BiSS
- Input / Output Circuits @nl7_servo
- ====== Input / Output Circuits ====== ===== Common Input circuit ===== The internal circuit of common in... are 2 types of outputs from master device: Relay output and Open Collector output as shown below. {{:nl7_servo:io_1.jpg?nolink&651x494|io_1.jpg}} ===== Common output circuit ===== There are 3 common outputs: DO1 an
- SIN/COS 1Vpp Output Signal @reverso_encoder
- ====== SIN/COS 1Vpp Output Signal ====== Example of SIN/COS Output (Blue and Yellow) with the encoder configured with 16mm of sine ... irect&650x449|sin_cos_2.jpg}} Example of SIN/COS Output (Blue and Yellow) with the encoder configured wit... ect&650x394|sin_cos_4_1.jpg}} Example of SIN/COS Output (Blue and Yellow) with the encoder configured wit
- MODBUS RTU Communication @integrated_drive_motors
- tion|2000|2008|8| |Input Variables|4096|4159|63| |Output Variables|4608|4671|63| |Oscilloscope data|4672|6... ister_microdrive.xlsx}} | ==== Digital Input and Output Signals ==== the integrated drive linear motors ... re protected against excessive voltage level. The output logic can be NPN (default) or PNP output with internal pull-up resistors.
- SIN/COS Encoder converter - Interpolator @miniature_motors
- IN/COS 1Vpp analog signal into Quadrature Digital output AB with TTL 5V level output. Furthermore, it can also convert the SIN/COS 1Vpp analog signal into digital output BiSS-C or SSI. This is necessary when the servo-d... le in index position and width\\ - Absolute angle output via fast serial interface (BiSS, SSI)\\ - Permane
- Cables accessories @motolab_actuator
- igital Input 2 (24V logic)| |10|DIG_OUT_1|Digital output 1 (24V logic, internal pull-up, NPN or PNP as default)| |11|DIG_OUT_2|Digital output 2 (24V logic, internal pull-up, NPN or PNP as default)| |12|DIG_OUT_VCC|Digital Output Vcc| |13|DIG_OUT_GND|Digital Output Ground| |14|ANALOG1-IN1|Analog Inpiut 1 - 0 to 10V programmable| |15|
- Connectors @motolab_actuator
- - Motion trigger 24VDC level| |5|DGT-OUT2|Digital Output 2 - programmable| |6|DGT-OUT-VCC|Digital output VCC| |7|DGT-OUT1|Digital output 1 - programmable| |8|AGND GROUND|Analog ground| |9|CAN-TERM|CAN H termina... T TX|Serial interface TX| |15|DGT-OUT-GND|Digital Output ground| |16|CONTROL SUPPLY|Power supply for contr
- Electrical characteristics @motolab_actuator
- rent|A|100 A| |Rated current (max)|A|50 A| |Rated output power (max)|A|3.6 kW| |PWM Frequency|kHz|10| ===... \\ Phoenix Contact TRIO-PS-2G/3AC/24DC/40. 24 VDC output 40 Amp Power Supply 3-phase 320 -575 Vac input. ... wer Supply, 100 → 240V ac ac, dc Input, 12V dc dc Output, 53A Output, 600W {{:motolab_actuator:omron_power.jpg?nolink&220x201|omron_power.jpg}}
- Register mapping @epulse50_dc_servodrive
- pulse50 registers are divided in Input Variables, Output Variables, Drive Parameters and Motion parameters... put variables|0x1000 to 0x103F|0x3000 to 0x303F| |Output variables|0x1200 to 0x123F|0x3200 to 0x323F| You... param.jpg?nolink&700x523|input_param.jpg}} ===== Output Variable Table ===== {{:mbd_servo_drive:var_out.
- Connectors and indicators @gdi_ethercat
- 24V logic)|Safe torque off| |10|DIG_OUT_0|Digital output 0 (24V logic, PNP)|Motor running| |11|DIG_OUT_1|Digital output 1 (24V logic, PNP)|Motor fault| |12|DIG_OUT_2|Digital output 2 (24V logic, PNP)|Programmable| ==== C4 connect