Fulltext results:
- Motor cooling @ironcore_motors
- m of heat. Due to the limited permissible winding temperature it must not exceed a specific value.\\ **Note: The maximum winding temperature rise of L-series motors is 105 K. This correspond... ors:technical_data|technical_data]])\\ fT: Factor temperature-related resistance raise\\ **Note: When you determine the power loss, you must take the temperature-related rise of the electrical resistance into ac
- Glossary
- heat the motor phases to their maximum operating temperature when the ambient temperature is 25°C, the motor is not moving, and there is no cooling.\\ **Continuous Force: ... mple: North\\ to North.\\ **Maximum** **Phase** **Temperature** \\ The maximum operating temperature for the motor phases. It is limited to provide a safe operating\\ tempe
- Liquid Cooled Motors (LK) @ironcore_motors
- hout aggressive additivies. * Rated water inlet temperature Tn= 20°C to 40°C * Water quality: The recommend... an overheated servo motor.__ Inlet cooling media temperature must be between 5° and 25°C to avoid condensation... nside of the motor; in any case the inlet coolant temperature must be higher than the motor frame temperature of at least 2°C \\ Before activating the motor, make sure the
- Transport and Storage @ironcore_motors
- owing storage conditions:\\ • Recommended ambient temperature: +15 to +25°C (+60 to +78°F),\\ • Permissible temperature: 0 to +70°C (+32 to +158°F), temperature fluctuation: < 10°C (18°F) per day.\\ • Relative humidity: < 65 % non... er damage to the servo motor. Condensation due to temperature fluctuations can result in electronic malfunction
- Faults Diagnosys and reset @integrated_drive_motors
- (dec)| |14|0xE|MOTOR_OVERTEMP|Motor & Drive over temperature|Reduce the acceleration rate or increase the wait... ime between the motion tasks. Check the threshold temperature level insider the NiLAB Starter - Paramenter 69 (... ime between the motion tasks. Check the threshold temperature level insider the NiLAB Starter - Paramenter 182
- NiLAB Starter Software @nilab_starter
- tic data are splitted into graphs \\ - Motor coil temperature filtered ## [2.3.1.7] - 02.10.2023 \\ - Added a ... - In diagnostic added gauge for Motor load, motor temperature and drive temperature \\ - Removed scale factors on the oscilloscope \\ - Change Automatic homing button to Re
- Technical Parameter @nl_eb15_safety
- sing cross-section|39 x 15 mm| |Ambient operating temperature |-10 to 55 degrees (without freezing)| |Storage temperature|-30 to 70 degrees (without freezing)| |Ambient operating humidity|When temperature is 20 degrees, humidity max 85%|
- Manufacturer responsibility
- llation and ambient conditions as described here (temperature, protection categories, humidity, EMC requirement... le, operation under water, in the case of extreme temperature fluctuations or extremely high maximum temperatur
- Can Open standard and extended PDOs @integrated_drive_motors
- t 13.3333px/inherit;;inherit;;inherit>Motor drive temperature</font> | <font 10pt/inherit;;black;;inherit>UINT... it;;black;;inherit>0x6055</font> |MOTOR / DRIVE TEMPERATURE | | <font 10pt/inherit;;black;;inherit>Command s
- Operating condition @integrated_drive_motors
- e linear motor are qualified to work with ambient temperature from 0 to +40 degrees Celsius.\\ The temperature of the motor winding is measured and monitor using I2T algoir
- Rules for the use of the product @mbd_servo_drive
- pressure on the packaging\\ During transport the temperature must be between -20 ° C and +75 °\\ C, max.rate o... the original manufacturer's packaging\\ • Storage temperature -20 ° C +75 ° C\\ • Storage relative humidity max
- Starter interface windows @nilab_starter
- trol on the motor parameters: nominal, peak, max. temperature, minimum DC power supply detection.\\ FW update a... storage for average current consumption and motor temperature with scope and save to file options.\\ Real time
- WEBSMART Motor sizing
- r parameters about payload, thrust force, ambient temperature and axis tilt. Then, the choice of the motor size
- Transportation and storage @green_drive_iso
- be protected against weather influence, with the temperature in the range of -5 up to +35 °C and at the humidi
- IP69K ISO Version @green_drive_iso
- istance * Resistance to consumption * Melting temperature: 2100 °C * Hardness: 500-600 HV * Suitable fo