Fulltext results:
- Protection
- |danger_e_symbol.jpg}} || | \\ **High electrical voltage! Danger to life, severe bodily harm by electric s... ction and safety regulations when working on high voltage installations. \\ * Before switching on power the... e. \\ * Before working with electrical parts with voltage higher than 50 V, the equipment must be disconnected from the mains voltage or power supply. \\ * Make sure the equipment can
- Force vs. speed curve
- e characteristic curves are defined by the DC bus voltage and the relevant motor-specific data, e.g. induct... tance and the motor constants. Varying the DC bus voltage (using different drives, power supplies or supply... }} When the velocity rises, the available DC bus voltage is reduced by the Back EMF of the motor. This lea... Where power supply motors with unregulated DC bus voltage are concerned, voltage drops – from simultaneous
- Glossary
- position.\\ **Back EMF: **The peak phase-to-phase voltage generated when the motor is traveling at a veloci... **Commutation: **The switching sequence of drive voltage into motor phase windings necessary to ensure con... g and there is no cooling.\\ **Continuous Working Voltage: **The maximum allowable continuous voltage between any two phases or between any phase and the motor safe
- Drive with analog reference @mbd_servo_drive
- erential analog input 12bit\\ Differentials input voltage of max. ± 10 V\\ Connect the controller (PLC or N... a potentiometer and you do not have a ± 10V dual voltage power supply, the voltage can be derived using the following circuitry. The first diagram shows how to drive the motor with a voltage from 0 to 10V, the second one with a voltage from
- Analog control @integrated_drive_motors
- ance here is 150 ohm, corresponding to a internal voltage of 3V. Using NiLAB Starter software the user can... otors:current_control.jpg?nolink&600x253}} ===== Voltage control (0 to 10V) ===== Voltage control can be used for position, force and velocity control as the Anal
- Directives @mbd_servo_drive
- ves ====== The EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC are mandatory for the supply... CE)\\ • EC EMC Directive (2004/108/EC)\\ • EC Low Voltage Directive (2006/95/EC)\\ The following rules must... ectrical Equipment in Machines)\\ EN 60439-1 (Low-voltage switchgear and controller assemblies)\\ The follo
- Electrical characteristics @motolab_actuator
- === |**Parameter** |**Unit** |**Value** | |Rated Voltage|V|24-48 VDC| |Minimum voltage|V|18 VDC| |Maximum voltage admitted|V|80 VDC| |Boost current (5sec)|A|120 A@5sec| |Peak current|A|100 A| |
- Holding brake @nl7_servo
- round motor with holding brake. * 24V operating voltage for the holding brake has to be ensured to mainta... onality of the holding brake. Please consider the voltage dropped over lengthy motor cables due to increase... nt malfunctioning of the holding brake in case of voltage drop. * If the motor is using a magnetic encode
- Safety instruction
- bol.jpg?nolink&110x127|danger_e_symbol.jpg}}|High voltage and high discharge current! \\ Danger to life or ... nk&110x117|warning_e_symbol.jpg}}|High electrical voltage due to wrong connections! Danger to life or bodil
- IP69K ISO Version @green_drive_iso
- 70x70mm. The available windings are both for high voltage (230/480 VAC) and for low voltage (24/48 VDC). {{https://en.nilab.at/wp-content/uploads//GDI-IP69K.11.jpg
- GDi - Green Drive ISO 15552 @green_drive_iso
- 70x70mm. The available windings are both for high voltage (230/480 VAC) and for low voltage (24/48 VDC). [[https://www.nilab.at/wp-content/uploads/ISO.jpg|{{https:
- Liquid Cooled Motors (LK) @ironcore_motors
- with the cooling liquid and \\ A) have a certain voltage drop according to the electro-chemical voltage order and \\ B) are electrically connected so that an elect
- Nidec M700 Servo Drive @lma_actuator
- n|32| |03.035|P1 Comms bits|26| |03.036|P1 Supply voltage|8V| |03037|P1 Comms Baud Rate|300k Baud| |03.038|... n|32| |03.035|P1 Comms bits|36| |03.036|P1 Supply voltage|5V| |03037|P1 Comms Baud Rate|1M Baud| |03.038|P1
- Safety @mbd_servo_drive
- ent injuries. Do not \\ work on the device if the voltage is connected. Wait at least 5 minutes, after \\ d... :caution_hot.jpg?nolink&166x184|caution_hot.jpg}}|voltage even though the motor is not rotating \\ temperat
- NL-EB15 Compact safety light curtain @nl_eb15_safety
- , the fastest response time < 1msec. * Low wide voltage power supply, the working voltage is 10 to 30VDC. * Good performance to resist electromagnetic interfere